- Easy Application
- Ultra-Low V.O.C. Formula
- High Bond Strength
- Strong Wet/Green Grab
- Minimal Shrinkage and Non-slump for Superior Contact
- High Elastomeric Properties
BondWise Adhesive
Advantages
Technical Data
TECHNICAL DATA | |
Base | Urethane Adhesive |
Consistency | Creamy liquid |
Color | Light Brown |
VOC Level | <30 grams/liter |
Trowelability | Smooth |
Shelf Life | One year in unopened container |
Storage | 40ºF -95ºF in cool dry location |
Application Temperature | 65ºF-95ºF (18º-35ºC) |
Tack Onset | 60 mins @ 70º F and 45% RH |
Traffic | Foot traffic in 12 hours, |
Flash Point | > 250º F |
Open Time | Up to 1.5 hrs at |
Freeze /Thaw | Storage above 40ºF in |
Surfaces must be clean and free from dirt, dust, debris, oils, waxes, or any other material that would inhibit bonding of the adhesive to the substrate, if some materials are difficult to remove, surface abrasion may be required. For use only in interior environments. Temperatures should be maintained as close to 70ºF and 45% relative humidity at least 72 hours before, during, and after installation of product. Floor moisture must be measured prior to installation. Maximum moisture presence is 3lb. Per 1000/sq.ft. per 24 hours, based on a Calcium-Chloride (CaCl) test, a maximum of a 4.5 reading on a TRAMEX Concrete Moisture Encounter, or 75% RH. Floor level can not exceed variance of 3/16” per 10 feet. Follow all surface preparation instructions issued by the manufacturer of wood finish surfaces.
In addition to these instructions, installers shall also refer to the most current edition of the following publications: American National Standards Institute (ANSI) publications. Tile Council of North America (TCNA) Handbook for Ceramic Tile Installations The Marble Institute of America (MIA) Dimension Stone Design Manual, NWFA (National Wood Flooring Association).
Condition finish flooring surface and install in accordance with wood manufacturers directions. Pour product over the correctly prepared surface, and trowel in place using a suitable notch trowel for the application of this product (see trowel chart). Using the incorrect trowel will void this adhesives warranty.
Press flooring firmly into BondWise™ UR-004 adhesive immediately after troweling. Starter rows should be taped to help prevent movement. Periodically check to make sure there is 100% adhesive coverage and transfer to the flooring. Do not spread more adhesive than can be covered in 45 minutes.
Use a weighted roller in accordance with wood manufacturer’s instructions. Allow a minimum of 4 hours to cure before light foot traffic can begin. Normal traffic can resume after 12 hours.
ONCE UR-004 CURES IT IS EXTREMELY DIFFICULT TO REMOVE AND WILL ETCH FINISH SURFACES.
See Technical Data Sheet for more information.
Urethane Adhesive PS-004
BondWise™ UR-004 is a superior component moisture curing urethane adhesive. UR-004 offers good wet / green grab, superior non-slump capability, and excellent shrink resistance allowing consistent contact between the wood flooring and substrate. UR-004 has high strength bond properties and superior elasticity.
Typical Uses
BondWise™ UR-004 can be used over both concrete and wood substrates to install finish wood surfaces including solid hardwood planks, laminate hardwood flooring, engineered hardwood flooring, and parquet flooring.
Trowels Recommendations
TROWELS AND COVERAGE | ||
Floor Product | Trowel | Coverage |
Engineered and Cork up to 7” wide and up to 5/8” thick. Solid and Bamboo up to 3” wide and up to 1/2” thick. | 50-55 ft2/gal. | |
3/16” x 1/4” x 1/2” | ||
Wood Flooring over 3” wide and up to 3/4” thick | 30-40 ft2/gal. | |
1/4” x 1/4” x 1/4” | ||
Finger Block Parquet, | 70-80 ft2/gal. | |
1/8” x 1/8” x 1/8” | ||
635 Old Hickory Blvd.
Old Hickory, TN 37138
© Copyright 2020 Wise Products, llc - Maintained by PhotoGraphycx, llc